Dolphin Wave 200 XL

Congratulations on your new Dolphin! We are so happy to have you as a part of the family!

After you have unpacked the robot and removed all the plastic wrapping it's time to start!

Preparing your Dolphin for use:

Step 1Preparing

• If your Dolphin has white climbing rings, make sure to remove the plastic wrap on the rings before starting the first cycle.
• Make sure that the power supply unit is placed at least 12ft (3.5m) from the edge of the pool and in the shade if possible. Our power supplies are splash-proof, but not waterproof.

Caution: We do not recommend using an extension cord.

• Release the minimum length of blue cable necessary to ensure that the robot will cover the entire pool. You can measure the amount of cable needed by measuring the longest part of the pool. Leave the excess cable rolled up outside the pool.
• Connect the blue cable to the power supply, align the plug on the connector with the notch on the power supply plug, and then turn clockwise until secure.
• Plug the power supply into a power outlet, but don't turn it on just yet!
• Place the Dolphin in the water in the middle of the longest part of the pool.

Step 2Launching

Getting started!

Place the Dolphin in the pool and let it sink to the bottom. In the case of brushes with foam rings, or foam brushes, press the brushes into the water until they are completely soaked.

Step 3Starting

You can now start your Dolphin robot using the ON/OFF button on your power supply.

Here is some additional information on how to use your Dolphin:

• Our Dolphin robots are designed to maintain the cleanliness of your pool once you have done your initial spring cleaning, activated the pool filtration, chemically balancing the pool, and removing major debris using your pool net.
• Our Dolphin robots can be equipped with fine spring filters that remove large debris (leaves, grass, twigs) and/or ultra-fine filters that can clean small particles (like sand or dust). We recommend using the spring filters for initial spring cleaning.
• Some models have adjustable handles to control the speed during the cleaning of the waterline.
• Make sure to never pull your Dolphin robot by the cable when it is in operation.
• At the end of each cycle, the Dolphin robot automatically turns off. If you stop the robot before the end of the cycle, (for example, because the filter is full), the unit will start the cleaning cycle from the beginning once it's turned on again.

If you want to know more about your robot features, we advise you to refer to the user manual of your robot.
You will need to indicate the model of your Dolphin or its serial number.

Open this answer on its own page →

(The picture is for illustrative purposes)

After each cleaning cycle, for optimal maintenance, we recommend removing the Dolphin from the pool and storing the robot and the power supply away from direct sunlight, excessive heat, or cold to prevent accelerated wear and tear.

Store the Dolphin robot in a shaded spot on the Dolphin caddy and wrap the cable carefully to prevent any kinks.

The power supply unit should be used in a covered, shaded area protected from the outdoor elements, including rain, heat, and cold. We recommend mounting the power supply on the Dolphin caddy or placing it on a higher surface away from the edge of the pool. The power supply unit should be positioned at least 12 ft from the pool.

If you are putting your Dolphin away for the season, for offseason storage, we recommend storing the Dolphin on the caddy and in a protected and well-ventilated area that is between the temperature 41°-113°F.

Keep the robot and power supply a reasonable distance from pool chemicals, as strong chemical fumes can be corrosive over time.

Open this answer on its own page →

It is important to maintain balanced pool chemicals since imbalanced chemicals can affect the Dolphin robot's efficiency. It can also cause premature wear and tear to the robot's components.

For example, if there is not enough chlorine, small algae deposits can clog the Dolphin filters and limit the motor's power. If the pH levels in the pool are higher than recommended, the robot will not climb the walls.

After doing a chemical shock/flocculant treatment it is important to wait 24 hours before putting the robot back in the pool.

Using the robot in the chemical and temperature levels outside of the following ranges can affect the proper function of the robot and can cause premature wear and tear.

These are the recommended chemical and temperature levels:

43-95°F (below 59°F climbing performance may be affected)

Our Dolphin robots can also be used in saltwater pools!

For optimal use and maintenance, the salinity levels should not exceed 5,000 P.P.M. We recommend rinsing the robot with tap water after each cycle to avoid buildup.

Open this answer on its own page →

You can complete your product registration and rebate submission through our online portal at https://registration.maytronics.com/.

Before you get started, make sure you have your robot’s serial number and your proof of purchase available.

You can find your Dolphin’s 10-character serial number located in these three places:

1. On the outside of the box on a white label
2. On your warranty card
3. On the inside casing of the Dolphin on a white label with a barcode

Follow the steps below to register your product:

1. Go to the registration portal: https://registration.maytronics.com/.

2. Enter your robot’s serial number: Type the serial number into the first field. If you need help locating it, click the “i” icon next to “Where do I find my robot’s serial number?”.

3. Select your previous pool-cleaning method, then click Continue.

4. Enter your personal information:

• As you begin typing your country or state, a dropdown menu will appear. Select the correct option from the list.
• Click Continue to move forward.

5. Rebate/Promotion Code Section:

• If you have a rebate or promotion code, enter it in the first field.
• If you do not have a code, leave the field blank and continue by selecting your purchase date.
• You may also add the store name, address, and ZIP code.

6. Upload your proof of purchase by selecting “Upload Your Receipt.” Accepted proof of purchase includes:

Preferred: Original receipt or original invoice (must show purchase date, product, and price).

If the original receipt cannot be located:

• A credit card statement or bank statement is acceptable.
• Only the date, merchant/product, and amount should be visible.
• Personal information must be hidden or removed.

7. Agree to the Terms & Conditions, then click Continue.

8. Review your information and click Submit to complete the registration.

To check your Dolphin’s warranty length, visit your model’s product page every Dolphin model. (Warranty lengths vary per model and region.)

Does your Dolphin need to be repaired? run the power supply checks to use our self-service tool to complete a warranty claim (RMA/Return Merchandise Authorization) to repair your Dolphin or to replace the power supply.

Open this answer on its own page →